I took the model out of the box, wound it up and got a 48 second test flight – GREAT!\u00a0 Maybe the best flight to date, although it was climbing dangerously high and getting close to the rafters.\u00a0 I wound up again and called for a time and I had NO success – the plane nosed up, stalled, fell off, and dove for the ground, cracking the propeller.<\/p>\n As I fixed the propeller, I notice one of the tail struts was loose.\u00a0 I did not fix it and it isn’t critical to flight.\u00a0 Since it was stalling on launch, I gave it more down thrust, and added clay to the nose (I should not have to do this – the model was flying well).\u00a0 I wound up again and gave it a gentle toss and had the same experience.\u00a0 This was\u00a0 a very stable model last month and even during the initial test flight that day?\u00a0 what had happened?\u00a0 I picked up the model and saw the wooden prop was broken in half – no more test flights that day.<\/p>\n Fixing it at home, I discovered what I think was the problem – and it was due to\u00a0 laziness or something even worse – careless disregard.\u00a0 While the prop was curing, I focused on that tail strut.\u00a0 I discovered that the horizontal stab was about 3\/8″ forward of where it should be.\u00a0 The h-stab and the fin have complementary notches and slide together and are then glued in place.\u00a0 Later the tails struts are glued in place.\u00a0 Here is where the carelessness comes into play:<\/p>\n I had not glued the h-stab to the fin.\u00a0 My post-crash analysis reveals that the h-stab would slide forward under a moderate sudden stop (inertia).\u00a0 Since the tail struts are a fixed length and glued solidly to the fin and the fuse, they would act as a pivot point – and force in a slight amount of negative incidence (up elevator).\u00a0 This would cause a nose up on launch that my chunk of clay and twist of down thrust could not overcome.<\/p>\n Lesson #1<\/strong> – always solidly fix your surfaces once you have a good-flying model.\u00a0 I don’t even do adjustable tails, so there was absolutely no reason I should not have glued that in the first place.\u00a0 This cost me damage to a good-flying plane: I broke the propeller, cracked the trailing edge of one wing, and tore the tail strut loose.<\/p>\n Lesson #2<\/strong> – if your plane suddenly misbehaves, THERE IS SOMETHING WRONG<\/span>.\u00a0 Do NOT continue flying it until you give it a full and critical examination.<\/p>\n Last week, I devoted a good 30 minutes or so to getting this plane to fly I stopped when I ended up with a cracked longeron and broken glue joints all along the length of the fuselage.\u00a0 This was not surprising considering how the plane tumbled when the flight was over.\u00a0 There was no landing with this plane – only crashes.<\/p>\n A couple of times I was able to get the model well up in the air, seemingly flying well.\u00a0 That is, until the power was low enough that it wouldn’t pull the plane around.\u00a0 Then the nose dropped.\u00a0 If the power came off under 10 feet, it simply looked like a steep dive into the ground.\u00a0 If the power came off at 20 feet, then the steep dive turned into a literal outside loop, with the model going beyond vertical before hitting the ground – hard.<\/p>\n The VAA (Volare Aviation Administration) review reveals that the h-stab is way too small on this model.\u00a0 If you recall, these 20″ Comet Dimer short kits are reproductions of the Comet kits – they event come with the original Comet Plans (well, downloaded scans, which are full of scan-upon-scan errors in addition to whatever initial design problems there were).<\/p>\n Archie Adamisin and I have done analysis on the six models.\u00a0 The Taylorcraft, Akron Funk, and the Spartan Fighter all have h-stabs that are too small.\u00a0 These produce models with TVo values under 0.4 – in the red zone.\u00a0 and this is caused by tails that are too small – these three will need the h-stab enlarged to 120% to give you a realistic chance at flying.\u00a0 Strangely – very strangely – the North American, the Vultee Attack and the Allied Sport all have TVOs well above 0.5 (0.6 will product a very stable model when properly trimmed).<\/p>\n I have added sheet wood to my h-stab on the Spartan and will resume flight trimming on this in January.<\/p>\n Lesson #3<\/strong> –\u00a0 always check your design before building.\u00a0 If I had not done the quick-and-dirty kit production and done my traditional draw-calculate-adjust-build-fly process, this would have been revealed.\u00a0 Imagine how many Comet Kids had similar frustrations and just smashed their models.<\/p>\n Lesson #4<\/strong> – How to launch a “floppy”, short-coupled, filleted model – hold the nose just in front of the wing to launch (not behind the wing).\u00a0 This it much like throwing a dart.\u00a0 Grasping in front of the CG results in much more consistent launches than grasping behind the CG.<\/p>\n Comet 5\u00a2 Scale – 3 fliers Now, I don’t know if Mike actually totaled three flights and I am sure that Winn only flew one flight.\u00a0 These little things are tricky.\u00a0 I have found the Cessna especially tricky.\u00a0 I believe that Mike built his from the Comet plans while Winn and I built our Cessnas from my short kit.\u00a0 My short kit followed the advice above and enlarged the tail 110% to produce a reasonable TVo of 0.65.<\/p>\n My Miller Racer is the more stable of the two models that I have built, so I flew that.\u00a0 My score is the total of three flights plus 11 bonus points (10 for low wing, 1 for landing gear down – Dime Scale bonus points).<\/p>\n Now I am not going to profess to know how to make these fly, but I will tell you about this model.\u00a0 The tail is enlarge 120% over the Comet plan. It has a Comet 4″ prop blank, cut down to 3.5″.\u00a0 I use a loop of 1\/16″ rubber.\u00a0 On my 28 second flight I put in about 1500 turns.\u00a0 It flies right under power.\u00a0 The glide is not much of a glide; more like a gentle fall.\u00a0 The prop is not freewheeling, so it just kind of brakes and spins, brakes and spins.\u00a0 Oh, and there is are several degrees of downthrust – the nose block is shimmed about 1\/16″ at the top.<\/p>\n I think there is a little more left in the tank in this model.\u00a0 I think that I will try a loop of 0.40″ or 0.045″\u00a0 – trying for less power and more duration.\u00a0 With 1\/16″ it takes off hard.\u00a0 The down thrust pulls it down for a time but eventually it climbs.\u00a0 Along with pulling it down, the initial flight is much like a bumblebee – darting all over the place.\u00a0 I launch with the plane banked to the left, maybe 25 degrees or more.\u00a0 This is done to the torque roll ceases about the time the model is in level flight.<\/p>\n Lesson #5<\/strong> – I don’t know if the above will work for everyone\u00a0 I just seemed to luck into it.\u00a0 I feel like I luck into a lot of success.\u00a0 But, being that there is a lot of success, it could be argued that not all of it is luck.\u00a0 One thing I know has helped me immensely – that is the Gizmo Geezer adjustable nose button.\u00a0 Much like Eli Manning and Frank’s Red Hot sauce, I put that s**t on everything (but not the Nickel kits – they are too small).\u00a0 This is not a product placement; I don’t care if you buy them from me or not – but you will have a much easier time trimming your thrust settings if you use an adjustable nose button.\u00a0 I also use Gurney flaps, clay on the wing tip, and huffing and twisting the wing panels – anything to get my models closer to the perfect flights that Tom Hallman and Wally Farrell have.<\/p>\n OOPS – LESSON #6<\/strong> – (this will make all of your trimming easier) – BUILD LIGHT<\/strong>.\u00a0 Build lighter than you think you can.\u00a0 Most of our models are over-built, structurally.\u00a0 Do NOT build them to survive a crash; build them light to avoid crashing.\u00a0 The Spartan Fighter above survived many hard landings because it is light.\u00a0 It only weighs 18.5g.\u00a0 Shoot for wing loadings under 0.4 grams per square inch and you will be rewarded.\u00a0 If you can get under 0.3 for Peanuts, that’s even better.<\/p>\n <\/p>\n <\/p>\n","protected":false},"excerpt":{"rendered":" Trimming the Model, that is; keep your models away from trees! While I have a degree of success in getting models to fly, I do not consider myself an “expert”.\u00a0 After 30 years of flying Free Flight, I still have … Continue reading ![\"\"](\"https:\/\/volareproducts.com\/new2024\/wp-content\/uploads\/2021\/11\/bf109-020.jpg\")
<\/a><\/p>\nExhibit #2 – the 20″ Comet Spartan Fighter.<\/strong>\u00a0 I had this model ready for November but it wouldn’t fly; it seems to be very sensitive on launch.\u00a0 It would either nose up or nose down immediately – something that some planes do what they are hard to grip (I usually see this on short-coupled planes or models with wing fillets – the Spartan is both).<\/h3>\n
<\/a><\/p>\nExhibit #3 – the Nickel Miller Racer.<\/strong>\u00a0 I think some people might be surprised by the performance of my tiny Miller Racer.\u00a0 Here are the official results (total of three flights) from the contest:<\/h3>\n
\n1st \u2013 George Bredehoft \u2013 Miller Racer – 81
\n2nd \u2013 Mike Welshans \u2013 Cessna – 14
\n3rd \u2013 Winn Moore – Cessna – 8<\/p>\n<\/a><\/p>\n