{"id":253,"date":"2013-05-06T19:21:40","date_gmt":"2013-05-06T23:21:40","guid":{"rendered":"https:\/\/volareproducts.com\/blog\/?p=253"},"modified":"2013-05-06T19:21:40","modified_gmt":"2013-05-06T23:21:40","slug":"i-coulda-been-a-contender","status":"publish","type":"post","link":"https:\/\/volareproducts.com\/new2024\/i-coulda-been-a-contender\/","title":{"rendered":"“I coulda been a contender!”"},"content":{"rendered":"

This is an inspiring, if not sad, tale of my Indoor Embryo experience this weekend.<\/p>\n

Sunday, our club (the Detroit Cloudbusters) held their annual Indoor Fling contest in the huge Ultimate Soccer Arena. \u00a0This indoor venue covers a full soccer field, roughly 250’x360′ and is 40′ high on the sides and 70′ high in the center. \u00a0The ceiling has girders, of course, but there is plenty of space to get in great flights and you should be able to trim just about any plane to fly within the confines.<\/p>\n

Being an outdoor flyer, I don’t have much opportunity, nor much cause to fly indoors. \u00a0In fact, I only fly one or two indoor events a year. \u00a0Saturday morning, I was contemplating the contest over my morning coffee, reviewing the event list and what planes I have that could fly in each. \u00a0Embryo was on the list and I had been casually considering building an Indoor Embryo for a month or two, but hadn’t got around to it.<\/p>\n

As flown under FAC rules, Embryo would be limited to the total of 3 flights with a 2 minute max on each flight. \u00a0Even indoor experts would be limited to 2 minutes – there’s no advantage to 4 or 5 minute flights! \u00a0I figured that I might be able to build an indoor (only) Embryo that I could be light enough that I might be able to extend the motor run to approach 2 minutes.<\/p>\n

Over winter, while thinking these thoughts, I had modified an existing plan (that I knew to fly well) to be bare minimum structure, but had not done any building. \u00a0I had two tasks for Saturday: grout the tile backsplash in the kitchen and pack the truck for the contest. \u00a0Well, three actually – getting a haircut got cut from the list as I made a decision: \u00a0I planned to squeeze building an entire plane from scratch in between the kitchen work and the truck packing. \u00a0I couldn’t pack the truck too late since we had to leave about 5:30 in the morning for the 2 hour drive over to Pontiac. \u00a0So…9am to noon was spent finishing up the backsplash – lots of work, but it looks good!<\/p>\n

After lunch, it was time to jump in. \u00a0The clock started at 1pm. \u00a0By 1:30, the wing was built. \u00a0By 2:10, the tail surfaces were built. \u00a0By 3:30 the fuselage was framed up. \u00a0By 6:45, everything was covered. \u00a0And finish assembly, nose block and landing gear put me at 11 grams and 8:30. \u00a0Test glides showed that I took too much weight out of the tail. \u00a0For me, that’s record time for a full-bodied plane. \u00a0I packed up my planes, packed up the merchandise and got to bed around 10pm.<\/p>\n

\"BCL-011\"<\/a><\/p>\n

\"\"<\/a>
\n11-12 grams on this 49.5 square-inch plane gave me hope that it would be possible to power this plane with a long loop of 1\/8″ rubber turning the 7″ prop. \u00a0The first task was to get the plane balanced and trimmed for circular flight. \u00a0I used a short motor and was pleased to see slow-climbing and slow-flying large circles, even though the circles could be a bit large. \u00a0Testing on this short motor (about 1000 turns) produced flights in the 40-50 second range – right where I hoped!<\/p>\n

\"BCL-013\"<\/a><\/p>\n

 <\/p>\n

I eventually got a longer motor installed (and fixed a faulty rear peg) and got about the business of re-trimming. \u00a0Things were looking good, but I just had to get those circles smaller. \u00a0I was getting a slow steady climb-out and I knew I would soon be able to put in some respectable official flights that would challenge for the lead. \u00a0Unfortunately, the fickle finger of fate pointed at my plane. \u00a0I couldn’t get the circles trimmed just right and at around 50 seconds into one of these test flights, my plane had drifted to the edge and, at about 45+ feet, it go caught inside what appears be part of the ventilation system – irretrievable.<\/p>\n

\"BCL-014\"<\/a><\/p>\n

 <\/p>\n

So ended my attempted foray into Indoor Embryo. \u00a0I won’t be taking that trip for about another 11 months!<\/p>\n","protected":false},"excerpt":{"rendered":"

This is an inspiring, if not sad, tale of my Indoor Embryo experience this weekend. Sunday, our club (the Detroit Cloudbusters) held their annual Indoor Fling contest in the huge Ultimate Soccer Arena. \u00a0This indoor venue covers a full soccer … Continue reading →<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[3,4],"tags":[],"class_list":["post-253","post","type-post","status-publish","format-standard","hentry","category-builds","category-events"],"_links":{"self":[{"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/posts\/253","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/comments?post=253"}],"version-history":[{"count":0,"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/posts\/253\/revisions"}],"wp:attachment":[{"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/media?parent=253"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/categories?post=253"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/volareproducts.com\/new2024\/wp-json\/wp\/v2\/tags?post=253"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}